(r5) Barrick Lab :: ProceduresStandardAgaroseGel

---+ Gel Electrophoresis

In order to analyze PCR results, the products are run on an agarose gel, which is then analyzed in UV light to ascertain the length of DNA fragments in the PCR reaction.

---+++ Making the Gel

Most PCRs can be analyzed on a standard 1% agarose gel (1g of agarose per 100 ml of buffer). Changing the concentration can be helpful for separating very large (use a 0.5% agarose gel) or very large size (use a 2% agarose gel).

For a standard 1% 50 ml gel:
   1) Add 0.5 g agarose and 50 ml TAE buffer to a 125 ml flask and heat in the microwave for 1:30 minutes. While the microwave is running you can set up the  gel mold and well combs. 
   2) After heating add 2.5 &#956;l SYBR Safe and swirl to mix. 
   3) Pour the liquid from the flask into the mold and let it solidify (approximately 20-30 minutes). 
   4) Once the gel has solidified:
   *  If using immediately, remove the comb, loosen the gel tray, and place the gel into a rig. Pour TAE buffer into the rig until the gel is thoroughly submerged.</br>
   *  If not being used immediately, the gel can be saved for later by wrapping it tightly in cellophane and storing in the 4 °C fridge.</br>

---+++ Loading the Gel

DNA samples should be mixed with a loading dye before loading.


First, gather all PCR products that are to be run, an appropriately sized ladder, and 6x loading dye. The latter two may be found in the 4 °C fridge in the computer room adjacent to the gel area. The 1 kb+ ladder is a combination 100 bp and 1 kb ladder which should be appropriate for any PCR sample (100 bp ladders are quite useful for samples less than 1500 bp, while 1 kb ladders are best suited for larger samples). 

   <img src="%ATTACHURLPATH%/10787018_1.jpg" alt="10787018_1.jpg" width='175' height='255.5' />

Basic Steps:
   1) Load 6 &#956;l of 1 kb+ ladder into the first well (dye is already combined with ladder)
   2) Combine dye and DNA on a cut out a sheet of parafilm. For each sample pipette 1 &#956;l of loading dye onto the parafilm. Then, mix 5 &#956;l of PCR product into a drop of dye and pipette up and down to mix. Finally, pipette the dye/sample mix into an empty well. Record which lane each sample is loaded into.
   3) Once all samples are loaded, attach the electrodes to the rig with the negative (black) electrode at the top and the positive (red) electrode at the bottom. Start the run from the power unit.

Note: Close PCR tubes when not being used. PCR products tend to dry up when exposed to air, leaving a lower volume that has a higher concentration of DNA.

---+++ Running the Gel

Steps:
   1) Once all samples have been loaded, attach a lid to the rig, and attach the lid to the Bio-Rad power supply (NOTE: always make sure that the current is off or paused before inserting or removing a cords from the power supply). 
   2) Set the voltage to 120 V and run the gel for about 20-30 minutes (you can set a timer on the machine itself by clicking on the clock logo. The run will stop when the time runs out). It is advisable to check up on the gel from time to time to make sure that it is proceeding normally. The tracking dye should migrate towards the bottom of the gel.
   3) When the gel seems to be completed, pause/stop the voltage, disconnect and remove the lid, and take the gel (in its tray) to the Bio-Rad gel imaging machine.

---+++ Imaging and Analyzing the Gel

Steps:
   1) Place the tray in the imager and open the Image lab program. 
   2) Select Protocol 1, then Position Gel, then OK on filter 2, then center your gel. 
   3) Once centered, close the imager door and select Run Protocol. 
   4) Modify the image as you see fit.*
   4) Save the image in Documents/[your name]. Note that the program saves files as .scn, which can only be opened by Image Lab and related programs. For a simpler version which can be viewed from any computer, select snapshot, then save a common file type (ex: .jpg). If you want a physical copy you can also print the image.

*Image lab contains several tools to aid in analyzing the gel image. Hitting the change contrast button allows manipulation of the brightness of the image, which may be helpful to clearly see faint bands. By clicking Lanes and Bands, then Automatic, the program puts labeled lanes where it perceives them. Bands can similarly be applied to the image.


---+++ Gel post-staining

Adding DNA dyes to agarose gels after electrophoresis (“post-staining”) can be advantageous when very crisp bands are needed (publication, low amount of DNA, etc).  Adding nucleic acid dye to the molten agarose can cause slight inhibit DNA migration and bending of bands. Post-staining can reduce bending, increase DNA signal, and reduce background signal

Steps:
   1) after gel electrophoresis, place gel into small tray
   1) add 15 µL of dye into 50 mL buffer (typically x1 TAE) and add to tray
   1) gently agitate for 30 minutes
   1) Remove buffer+dye
   1) wash gel with ddH2O 2-3 times
   1) image gel

*Notes:*
1. 15 µL of GelRed into 50 mL buffer is the correct dilution
2. [[https://tools.thermofisher.com/content/sfs/manuals/sybr_safe_dna_gel_stain_man.pdf][SYBR-safe gel documentation]] notes that 50 µL of dye should be added to 50 mL buffer, though 15 µL of dye into 50 mL like likely sufficient (not tested)
3. Typically, dye is diluted in the same buffer that the gel is made of/was run in (e.g.: x1 TAE)
4. any volume of buffer+dye can be used, though it must completely cover the gel
5. Post-staining buffer can be reused up to 5 times by storing in dark storage container (e.g.: a 50 mL conical tube covered with aluminum foil)
Barrick Lab > ProtocolList > ProceduresStandardAgaroseGel
Contributors to this topic
IsaacGifford, KateElston, AurkoDasgupta, MattMcGuffie
Topic revision: r5 - 2023-09-20 - 00:15:43 - Main.IsaacGifford